⏱ 10 min read  ·  ✅ Updated Nov 2026

Small heatsinks only help VRAM, VRM and chipset parts if they stay attached. Many graphics cards and motherboards give those parts no screw holes, clips or push pins, so a finned block has nothing mechanical to hold it down. Thermal adhesive solves that problem: a paste or glue that transfers heat and bonds the heatsink in place as it cures.

Our top pick: GENNEL G109 10gram Thermal Conductive Glue. Runner-up: Arctic Silver Ceramic Thermal Epoxy ACE-6G.

This guide covers adhesive compounds only. Thermal tape is a different product class, and ordinary paste never sets, so it cannot hold a heatsink on a vertical card by itself. Every pick below is a genuine bonding compound: a one-part silicone plaster, or a two-part epoxy. Read the permanence warnings carefully, because several of these bonds are effectively forever, and one pick is electrically conductive by design.

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

For most small heatsink jobs, start with a one-part silicone plaster such as the GENNEL G109, which needs no mixing and stays flexible after curing. Choose a two-part epoxy when the heatsink sits vertically or the bond must be permanent. Keep the layer thin, respect the full cure time, and never use adhesive under a main GPU or CPU cooler.

How to Choose

Start with the chemistry, because it decides almost everything else. One-part silicone plasters cure in air, need no mixing, and form a rubbery bond that tolerates vibration and thermal cycling. That flexibility also makes later removal less destructive. Two-part epoxies cure into a hard, rigid solid and hold heavier heatsinks on vertical surfaces with far more confidence. The trade is permanence: a cured epoxy bond usually cannot be separated without risking the component underneath.

Next, check working time against the job size. Fast epoxies thicken within minutes, fine for one memory heatsink but punishing across a full row of VRM sinks. Slow-cure formulas give more adjustment time, but the card must sit undisturbed until the bond sets. Silicone plasters reach full cure over about a day, so plan around that wait.

Electrical behavior matters on crowded boards. Ceramic-filled and silicone adhesives are electrically insulating, which is forgiving around exposed memory pins. Silver-filled epoxy is engineered for high electrical resistance, yet its maker warns users to keep it away from traces, pins and leads, because the cured material is slightly capacitive. One specialist epoxy here goes further and is fully electrically conductive, limiting it to jobs where a conductive joint is acceptable and every nearby lead can be masked. If squeeze-out could reach anything conductive, choose an insulating formula.

Bond-line thickness controls heat transfer more than headline conductivity figures do. Every product in this class rewards a thin, even layer and penalizes a thick blob, because the adhesive is always the weakest thermal link in the stack. Press the heatsink down firmly, twist it slightly to spread the compound, and wipe away squeeze-out before it cures.

GENNEL G109 10gram Thermal Conductive Glue

The GENNEL G109 is the simplest entry point here: a one-part silicone thermal plaster in a small tube, sold for heatsinks that have no fixed clip. The listing describes strong adhesion with heat-conducting filler, a non-conductive and flame retardant formula, and a wide working temperature range covering anything a memory or chipset heatsink will see. With no mixing, the job is cleaning both surfaces, applying a thin film, and seating the heatsink.

Specs

    Item Detail
    Brand GENNEL
    Model G109
    Pack size 10 grams
    Chemistry One-part silicone plaster
    Full cure time 24 hours
    Working temperature -60 to 280 degrees C
    Electrical behavior Non-conductive
    Suggested layer 0.1 to 0.5 mm, thinner preferred

    The listing is direct about limits: it tells buyers not to use thermal glue between a CPU and its heatsink, and that warning applies to the main GPU die too, because clamped coolers need paste. The G109 fits the job in its title: small sinks on MOSFETs, memory chips and chipsets that run warm rather than extremely hot.

    The plaster is viscous, so it stays where placed instead of running toward nearby pins, which helps around dense VRM layouts. Seat each heatsink once, hold it briefly, then leave the card flat and untouched until full cure. Repositioning mid-cure tears the forming bond and leaves a weaker, thicker layer. Choose the G109 when heatsinks are light and future removal remains a possibility: the flexible silicone gives up some holding strength versus epoxy, and in return is the least intimidating product here to live with afterward.

    Arctic Silver Ceramic Thermal Epoxy ACE-6G

    This six-gram set takes the opposite approach: two small syringes, resin and hardener, mixed in equal amounts just before use. The listing describes a permanent, high-performance adhesive for bonding heatsinks where mounting hardware cannot be used, filled with aluminum oxide and boron nitride ceramic particles. Those fillers are the point: they move heat while keeping the cured bond electrically insulating.

    Specs

      Item Detail
      Brand Arctic Silver via ModMyMods
      Model ACE-6G
      Pack size 6 grams total
      Format Two 3 g syringes
      Mix ratio 1 to 1
      Filler Aluminum oxide and boron nitride ceramic
      Electrical behavior Electrically insulating
      Stated uses CPU, GPU, RAM, VRM and chipset heatsinks

      That use list needs one clarification. The epoxy suits small auxiliary heatsinks on RAM, voltage regulators and chipsets. It is not permission to glue a main processor cooler down, because a permanent bond under a large cooler makes every future removal destructive. Pick this set when permanence is the goal: a card that will run for years with add-on memory sinks, or a chipset heatsink that keeps loosening under other methods. If the heatsink might come off again, a silicone plaster is the kinder choice.

      Arctic Silver Arctic Alumina Thermal Adhesive AATA-5G

      Arctic Alumina thermal adhesive is one of the oldest names in this category, a two-part ceramic epoxy set that predates most graphics cards it might be used on. The five-gram AATA-5G set built its reputation on a simple promise: when a heatsink absolutely has to stay on, this class of product keeps it on. Its ceramic composition carries a second benefit: no danger of a short circuit from the adhesive itself.

      Specs

        Item Detail
        Brand Arctic Silver
        Model AATA-5G
        Pack size 5 grams
        Chemistry Two-part ceramic epoxy adhesive
        Filler type Ceramic alumina
        Electrical behavior Non-conductive ceramic composition
        Format Two-part set, mixed before use
        Typical targets Small heatsinks on chips and shims

        Availability is the honest caveat here. Price tracking shows an old product with no current tracked offer. Treat it as a legacy option to source from a reputable seller, and check the set is complete and unopened, since aged epoxy does not improve with time. Choose Arctic Alumina when a ceramic, electrically safe epoxy is the priority and a genuine set can be sourced. Anyone needing guaranteed fresh stock today should start with a currently listed option.

        Arctic Silver Premium Silver Thermal Adhesive ASTA-7G

        The ASTA-7G set is the silver-filled sibling in this family: seven grams across two syringes, mixed in equal parts, and rated by the maker well above the conductivity of ceramic or silicone formulas. Silver filler is how the number gets there, and why this product carries a strict warning in the group: the adhesive is engineered for high electrical resistance, but it must be kept away from traces, pins and leads, and the cured material is slightly capacitive.

        Specs

          Item Detail
          Brand Arctic Silver
          Model ASTA-7G
          Pack size 7 grams total
          Format Two 3.5 g syringes plus mixing wand
          Chemistry Two-part silver-filled epoxy
          Bond type Permanent
          Electrical behavior High resistance, slightly capacitive when cured
          Typical targets RAM chips, MOSFETs and small heatsinks

          On the flat, open top of a memory chip or MOSFET with clear space around it, application is straightforward and the thermal payoff is real. In a tight valley between tall capacitors and exposed leads, the balance flips, and an insulating ceramic or silicone product is the responsible pick. Like the Alumina set, this is a legacy listing with no current tracked offer, so sourcing takes care: verify the set is the adhesive, not the far more common Arctic Silver paste sold under a similar name. Reach for the ASTA-7G when maximum heat transfer through a permanent bond decides the choice and the area is clean, flat and electrically uncluttered.

          Atom Adhesives AA-Duct 902 Silver Epoxy Adhesive

          Atom Adhesives builds epoxies for electronics work, and the AA-Duct 902 is its pure-silver formulation: a two-part epoxy adhesive sold as a small 2.5 gram kit. Maker documentation describes maximum continuity of conductivity from the silver filler, a wide operating temperature range, and a cured thermal conductivity figure above the ceramic and silicone options here. That combination comes with the sharpest condition in this roundup, covered below.

          Specs

            Item Detail
            Brand Atom Adhesives
            Model AA-Duct 902
            Pack size 2.5 gram kit
            Chemistry Two-part silver-filled epoxy
            Cure type Room temperature or heat cure
            Full cure time 24 hours
            Operating temperature -50 to 170 degrees C
            Thermal conductivity 2.99 W per mK per maker data
            Electrical behavior Electrically conductive, by design
            Typical substrates Aluminum, copper, ceramic, glass and board materials

            The condition is electrical. Unlike every other pick here, this epoxy is meant to conduct electricity, so it belongs only where a conductive joint is acceptable: bonding a heatsink to a grounded metal surface, or a chip package top with every pin and lead masked well clear of the bond line. On a crowded VRAM or VRM row, an insulating adhesive is the safer tool, full stop.

            Where the fit is right, the appeal is a documented industrial epoxy with high cured strength and room-temperature curing. The small kit size suits one or two sinks rather than a full card, so count the job before mixing. Choose the AA-Duct 902 when a conductive epoxy joint is specifically what the job calls for and the work area can be kept electrically clean. Everyone else should treat it as the specialist outlier in this group, not the default.

            Who Should Skip It

            Skip thermal adhesive entirely if the cooler uses screws, clips, push pins or a bracket. Mechanical mounting with ordinary paste is stronger, serviceable and safer, and gluing a clamped cooler down only creates a future failure. The main GPU die and the CPU belong in this category without exception.

            Skip it, too, if the card carries a warranty that matters, if resale is planned, or if the heatsinks are experimental and likely to be swapped after temperature checks. Epoxy removal risks lifting pads and tearing components. Trial-fit first, confirm temperatures justify permanent sinks, and only then commit. Finally, skip silver-filled and conductive epoxies when the work area is electrically crowded, and skip every product here if ventilation, gloves and unhurried time are unavailable. A half-cured heatsink that lets go inside a running system is worse than no heatsink at all.

            FAQ

            Is thermal adhesive better than thermal paste for VRAM heatsinks?

            They solve different problems. Paste transfers heat slightly better but holds nothing in place, so a paste-only VRAM heatsink on a vertical card will eventually slide or fall. Adhesive trades a little thermal performance for a bond that keeps the sink seated for years.

            Can a heatsink bonded with thermal epoxy be removed later?

            Plan on no. Cured epoxy bonds are treated as permanent, and forced removal can tear the chip or its solder joints with the heatsink. Silicone plaster bonds are more forgiving and can sometimes be worked free slowly, but even those removals carry risk. Choose the chemistry with removal in mind before mixing.

            How long should a bonded heatsink cure before the card is used?

            Follow the full cure time, not the initial set time. The silicone plaster here lists a full day, the silver epoxy kit lists a full day at room temperature, and fast epoxies still gain strength over hours after they feel hard. Powering the card early heats a weak bond and invites it to creep or release.

            Why not just use thermal tape on every small heatsink instead?

            Tape is cleaner and removable, and is covered as its own topic elsewhere. Its limits are holding strength on heavier sinks and sensitivity to surface preparation. Adhesives exist for jobs where tape has let go, or where the heatsink cannot move.

            Final Verdict

            Match the chemistry to the commitment. The GENNEL G109 covers most home VRAM, VRM and chipset jobs with the least fuss and the gentlest aftermath. The Arctic Silver ceramic epoxy set serves builders who want a permanent, insulating epoxy bond in a currently listed set. The legacy Alumina and ASTA-7G sets remain worth sourcing for ceramic safety or maximum conductivity, provided genuine fresh stock can be verified first. The Atom Adhesives AA-Duct 902 is the narrow specialist: a conductive silver epoxy for jobs that explicitly accept a conductive joint.

            Product and ASIN Reference

            Product ASIN
            GENNEL G109 10gram Thermal Conductive Glue B072MSXHJD
            Arctic Silver Ceramic Thermal Epoxy ACE-6G B0GNHNJS1Y
            Arctic Silver Arctic Alumina Thermal Adhesive AATA-5G B0009IQ1BU
            Arctic Silver Premium Silver Thermal Adhesive ASTA-7G B0087X7262
            Atom Adhesives AA-Duct 902 Silver Epoxy Adhesive 2.5g Kit B00EPYCIGQ

            Explore Our Guides & Free Tools