⏱ 8 min read  ·  ✅ Updated Nov 2026

Table of Contents

Quick Answer

A DisplayPort splitter takes one DisplayPort output from a PC or graphics card and feeds two monitors, either with the same mirrored image or, through Multi-Stream Transport (MST), with two independent extended desktops. For most dual-monitor desks, the THANDBLE splitter leads this group because it pairs a DisplayPort 1.4 input with two DisplayPort outputs that each run 4K at 60 Hz in extended mode. The SIIG CE-DP0H11-S1 is the mid-range pick for DisplayPort 1.2 systems, with a documented panoramic video wall mode on top of mirror and extended modes. The gofanco DPMST2DP covers the budget tier for dual 1080p or dual 4K at 30 Hz office work. When the monitors on the desk take HDMI rather than DisplayPort, the DGYBDFC and XPTSFDU adapters convert one DisplayPort 1.4 input into two HDMI 2.0 outputs at up to 4K at 60 Hz. Every pick here is a 1-in-2-out device; none of them is a switch for sharing one monitor between two computers.

As an Amazon Associate, we earn from qualifying purchases.

How Compared

Each splitter was compared on published specifications only, using the figures in its Amazon listing data and maker documentation. Four axes decided the lineup. The first is output type crossed with output count, because a hub feeding two DisplayPort monitors does a different job from one feeding two HDMI monitors. The second is the DisplayPort version as published, since version 1.2 devices share 21.6 Gbps of bandwidth while version 1.4 devices share 32.4 Gbps, and that shared pool sets the ceiling for both screens together. The third is the published mode list: mirror, extended and panoramic video wall support, plus any platform limits the maker states. The fourth is the power arrangement, because every device here draws power over USB or from an included supply rather than from the DisplayPort connector alone. Prices are not compared; each splitter sits in a budget, mid-range or premium tier instead. Where a headline figure and the specifications section disagreed, the specifications figure is the one used here.

One limit applies to the whole category: extended desktop mode depends on MST support in the host graphics hardware and works on Windows, while macOS limits these splitters to a mirrored image on both screens.

THANDBLE DisplayPort to Dual DisplayPort Splitter

Check price on Amazon

The THANDBLE splitter is the premium pick for a desk that wants two DisplayPort monitors at full 4K pace from a single port. Its listing describes a DisplayPort input feeding two DisplayPort outputs, with MST carrying two independent pictures at 4K and 60 Hz per screen on a Windows host. Mirror mode is also supported for presentation setups where both screens must show the same image. The maker positions the adapter for desktop PCs and graphics cards with a native DisplayPort output, and it notes that the signal runs one way only, from the computer to the monitors. For a gaming or productivity desk built around a modern NVIDIA or AMD card with one free DisplayPort socket, this is the cleanest path to a matched pair of 4K panels.

Specs

  • DisplayPort version: 1.4
  • Outputs: 2 x DisplayPort
  • Max resolution per output: 3840 x 2160 at 60 Hz with both outputs active
  • Modes: MST extended and SST mirror
  • Power source: USB powered, 5 V

SIIG 1×2 DisplayPort 1.2 MST Splitter (CE-DP0H11-S1)

Check price on Amazon

SIIG builds this hub for DisplayPort 1.2 systems, and its published documentation is the most detailed in this group. The hub takes one DisplayPort 1.2 input and drives two DisplayPort monitors, with a single screen reaching 4K at 60 Hz and a dual-screen extended desktop running at 4K and 30 Hz per screen inside the 21.6 Gbps bandwidth pool. Alongside mirror and extended modes, SIIG documents a panoramic mode that spans one image across both displays, which suits wide dashboards and signage pairs. The hub passes 7.1 channel audio and draws its power over USB at 5 V and 500 mA, so a spare motherboard port covers it. SIIG states Windows support for extended mode, with macOS limited to mirroring. It sits in the mid-range tier and fits older workstations that predate DisplayPort 1.4.

Specs

  • DisplayPort version: 1.2
  • Outputs: 2 x DisplayPort
  • Max resolution per output: 3840 x 2160 at 60 Hz for one screen, 3840 x 2160 at 30 Hz per screen with both outputs active
  • Modes: MST extended, SST mirror and panoramic video wall
  • Power source: USB powered, 5 V at 500 mA

gofanco 1×2 DisplayPort 1.2 Splitter (DPMST2DP)

Check price on Amazon

The gofanco DPMST2DP is the budget-tier route to two DisplayPort monitors from one DisplayPort 1.2 output. Its listing describes an MST hub that extends a Windows desktop across two screens at up to 4K and 30 Hz each, or mirrors a single 4K image at up to 60 Hz when only one output is in play. That profile fits office work, coding and document-heavy desks where 1080p and 1440p panels are common and the 30 Hz ceiling at 4K rarely bites. The maker is explicit that extended mode is a Windows feature, and that the hub needs USB power connected to run. For a spare desk or a second workstation built from an older graphics card, the gofanco covers the dual-monitor basics without paying for DisplayPort 1.4 headroom that the host cannot use.

Specs

  • DisplayPort version: 1.2
  • Outputs: 2 x DisplayPort
  • Max resolution per output: 3840 x 2160 at 30 Hz per screen with both outputs active
  • Modes: MST extended and SST mirror
  • Power source: USB powered, 5 V

DGYBDFC DisplayPort to Dual HDMI Adapter

Not every dual-monitor desk is wired for DisplayPort on the screen side, and the DGYBDFC adapter covers that case. It accepts a DisplayPort 1.4 input from a PC, laptop or graphics card and converts it to two HDMI 2.0 outputs, each rated for 4K at 60 Hz, so a pair of HDMI monitors or TVs can run from one port. The listing describes an MST extend mode for Windows, giving two independent screens, and a mirror mode for shared viewing; macOS is limited to mirror mode. Because the conversion happens inside the adapter, the host still needs a DisplayPort 1.4 output with MST support for extended desktops. It sits in the mid-range tier and suits desks where the monitors are already chosen and HDMI is the input they offer.

Specs

  • DisplayPort version: 1.4 input
  • Outputs: 2 x HDMI 2.0
  • Max resolution per output: 3840 x 2160 at 60 Hz with both outputs active
  • Modes: MST extended on Windows and SST mirror
  • Power source: USB powered, 5 V

XPTSFDU DisplayPort to Dual HDMI Splitter

Check price on Amazon

The XPTSFDU splitter is the second HDMI-output option in this group and lands in the budget tier. Its listing data describes one DisplayPort 1.4 input and two HDMI 2.0 outputs with a maximum resolution of 4K at 60 Hz and a video bandwidth of 18 Gbps. Extended mode shows three different images across the host screen and the two monitors on Windows, while mirror mode repeats one image; macOS supports mirror mode only. The maker notes that the host must support DisplayPort 1.4, that the input cable should stay at or under 1.8 metres, and that a power cable is included in the box because the splitter needs external power to run. For a home office pairing two HDMI screens with a desktop that has a single free DisplayPort socket, it covers the requirement with the fewest extras.

Specs

  • DisplayPort version: 1.4 input
  • Outputs: 2 x HDMI 2.0
  • Max resolution per output: up to 3840 x 2160 at 60 Hz
  • Modes: MST extended on Windows and SST mirror
  • Power source: external power, cable included

How to Choose a DisplayPort Splitter

Begin with the monitors, because their inputs decide the output type. A pair of DisplayPort monitors calls for a DisplayPort-output splitter such as the THANDBLE, SIIG or gofanco, while HDMI screens need a conversion adapter such as the DGYBDFC or XPTSFDU. Next, match the DisplayPort version to the host. A DisplayPort 1.4 graphics card can feed two 4K screens at 60 Hz through a version 1.4 splitter, while a DisplayPort 1.2 host shares 21.6 Gbps, which means two 4K screens at 30 Hz or two 1440p screens at comfortable refresh rates. Then confirm the mode you actually need. Mirror mode works almost everywhere, but an extended desktop needs MST support in the graphics hardware and a Windows host; macOS mirrors through every device in this category. Finally, plan for power. Each splitter here needs a USB port or its included power cable connected, and a hub left unpowered is the most common cause of a dark second screen. Keep the input cable short and rated for the DisplayPort version in use, and keep splitters separate from switches in your thinking: a splitter sends one computer to two monitors, while a switch sends two computers to one monitor.

FAQ

Can a DisplayPort splitter show two different images on two monitors?

Yes, when the splitter and the host both support MST. On a Windows PC with an MST-capable graphics card or integrated GPU, a splitter such as the THANDBLE or SIIG runs in extended mode and each monitor shows its own desktop. Without MST, the same hardware falls back to mirror mode and both screens show one identical image.

Why does a Mac only mirror the image through an MST splitter?

macOS does not support MST for external displays over a single port in the way Windows does, so every splitter in this group treats a Mac as a mirror-mode host. The makers state this limit in their own documentation, and it applies to DisplayPort-output and HDMI-output models alike. Mac users who need two independent screens should use two separate ports on the machine instead.

Does a DisplayPort splitter need its own power supply?

Yes, in practice every model in this group needs power connected before both outputs run reliably. Most draw 5 V over a USB cable from the host or a wall adapter, and the XPTSFDU includes its power cable in the box. Leaving the power lead disconnected is a common cause of flicker or a second screen that never wakes.

What is the difference between a DisplayPort splitter and a DisplayPort switch?

A splitter is a 1-in-2-out device that sends one computer to two monitors at the same time, in mirror or extended mode. A switch runs the other way, connecting two computers to one monitor and selecting which one is shown. The two devices solve opposite problems, and a switch cannot extend a desktop across two screens.

Conclusion

Two monitors from one DisplayPort socket is a solved problem once the splitter matches the desk. Choose the THANDBLE for dual DisplayPort 4K at 60 Hz, the SIIG for a documented DisplayPort 1.2 hub with a panoramic mode, and the gofanco for a budget dual-screen office setup. When the screens speak HDMI instead, the DGYBDFC and XPTSFDU convert one DisplayPort 1.4 output into two HDMI feeds at up to 4K and 60 Hz. Whichever tier fits, confirm MST support on the host, connect the power lead, and the second screen becomes part of the workspace rather than a cable puzzle.

Explore Our Guides & Free Tools